Новые поступления

Jtron M542V 42/57-Type Two-Phase Stepper Motor Driver - Black 57 two phase stepper motor drive current 4 2a 1850v breakdown 542 128
Product Overview M542V2.0 type drive motor has a lower heat noise and higher running smoothly primarily driven 42 57-type two-phase hybrid stepping motor. Micro-step subdivision have 15 species the maximum number of steps to 25000Pulse/rev; their work peak current range of 1.0A~4.2A output current total have eight files the current resolution is about 0.45A; with automatic half current overvoltage and overcurrent protection functions. The drive is a DC power supply recommended operating voltage range of DC 24~36V voltage does not exceed DC 50V not less than DC 20V. Drive function Micro-step the number of subdivision settings: Drive function Micro-step subdivision the number of settings: By the SW5-SW8 four DIP switches to set the number of micro-step subdivision the drive which has 15 files micro-step. When users set the micro-step you should stop the drive to run. Output current setting: the SW1-SW3 three dial switch to set the driver output current the output current total of eight files. Automatic half current function: Users can set up automatic half current function drives through SW4.Off represents the quiescent current is set to half the dynamic current on represents a static current and dynamic current of the same. General applications should take SW4 set to off that the motor and the drive to reduce fever increased reliability. After a burst of about 0.4 seconds to stop automatically reduced to about half of the current (60% of the actual value) reduced to 36% of the theoretical heat. Signal Interface: PUL + and PUL-control pulse signal positive terminal and a negative terminal; DIR + and DIR-signal for the direction of the positive terminal and a negative terminal; ENA + and ENA-enable signal to the positive terminal and a negative terminal. Motor Interface: A + and A- connected to the positive and negative terminal of the stepper motor A phase winding; B + and B- connected to the positive and negative terminal of the stepper motor B phase winding. When the A B two-phase windings exchange can reverse the motor direction. Power Interface: DC power supply operating voltage range is recommended for the DC 20~50V Power greater than 100W. Indicator: drive has red and yellow these two kinds of lights when the drive is powering the green light on; Red is a fault indicator when an overvoltage overcurrent fault the fault lights lit. After the fault is cleared the red light is off. When a drive fails only the power on again and re-enabled in order to clear the fault. Installation Instructions Installation pitch of 112mm both horizontal and vertical installation we recommend using the vertical installation. When installed it should be close to the metal cabinet to facilitate cooling.
3687.28 RUR
Jtron 2M542AH Stepper Motor 57 / 86 Driver Board for Engraving Machine - Black 57 two phase stepper motor drive current 4 2a 1850v breakdown 542 128
1. The main driver of 57 86-type two-phase hybrid stepping motor 2. The number of subdivision 14 species the maximum number of steps is 256 subdivision; 3. The operating current range of 1.0A~6A output current total have 11 files; 4. With automatic current control function the current flow is adjustable semi-automatic this feature is no other drives of the same type which can adjust the intensity of the motor locked when no impulse control. 5. The drive voltage DC power supply. Operating voltage: DC 18~85V voltage do not exceed the maximum operating voltage it is recommended to use a DC 60V or less. 6. This paragraph has driven decay mode adjustment function this function is the same type of drive is not the other it can better match the different motors vibration and noise will be reduced to the lowest. 7. With undervoltage and overvoltage protection. Function Description: Output current setting: the potentiometer setting driver output current the output current total have 11 files. The number of subdivision setting: The SW1-SW4 this four dial switch to set the number of micro-step subdivision the drive which has 14 files micro-step. When users set the micro-step you should stop the drive to run. Automatic current function: Users can through SW7 SW8 to set the drive automatic semi-flow feature. Attenuation setting: the SW5-SW6 This two DIP switches to set the drive decay modes. Signal Interface: PUL + and PUL-control pulse signal positive terminal and a negative terminal; DIR + and DIR-signal for the direction of the positive terminal and a negative terminal; EN + and EN- is the enable signal of the positive terminal and a negative terminal. Motor Interface: A + and A- connected to the positive and negative terminal of the stepper motor A phase winding; B + and B- connected to the positive and negative terminal of the stepper motor B phase winding. When the A B two-phase windings exchange can reverse the motor direction. Power Interface: V + connected to the supply positive V- connected to the supply of negative positive and negative not reversed. Indicator: drive has red and yellow these two kinds of lights the green light for the power indicator light when the drive is powering the green light on; Red is a warning indicator in the protection of the state the light is on. Installation instructions Can be vertical or horizontal installation installation should make it close to the metal cabinet to facilitate heat dissipation. Scope of application Mainly used to drive 57 86 of the 2 phase stepper motor. On the strength location has certain requirements of the occasion to achieve precise control such as CNC feeding machine CNC cutting machine. Computer engraving machine CNC lathe CNC.
2871.58 RUR